- Opening diameters: 25 mm - 38 mm
- Grid clamp / truss tube pipe clamp
- M12 locking bolt with butterfly nut
- Spigot receiver 16 mm (5/8")
- Interior rubberized surface
- Fully metal made
- Size: 9.5 x 8 x 3 cm | 0.35 Kg
- Payload: 25 Kg
HMI PAR 6000 watts kit
- Power: 6000W
- Daylight-balanced (6000K) spotlight
- Single ended line of Metal-Halide lamps (HMI*)
- Front UV protective glass with safety wire mesh
- Optional spread lenses for beam angle variations
- Sturdy die cast aluminum construction
- Includes: ballast, power cable, barndoors, case
- DMX512 control optional
€13'99900
Available only on pre-order with delivery time of 8-12 weeks.
Powerful daylight-balanced light source
The Cinelight PAR HMI lights are best suited for motion picture, events and TV productions where the maximum light output is required. PAR fixtures are recommended to be used for lighting background elements or diffused / bounced into a white reflector panel to act as a soft fill light for talents (PAR lamps are too hard sources to be used for lighting faces directly).
Optional spread lenses for beam angle variations
The Cinelight PAR HMI lights come with clear, UV protective glass in front topped up by a safety wire mesh. Optional drop-in spreader lenses can be used to fine-tune the light output from wide flood to narrow spot variations, in order to obtain the optimal beam angle. The spreader lenses affect both the shape and angle of the beam and are available to be purchased separately.
Fully die cast aluminum housing
The Cinelight PAR HMI is using a series of aluminum extrusions and aluminum corrosion castings for the housing to quickly dissipate the heat that comes from the light bulb, therefore increasing the lamp's life. The amount of time needed for the fixture to cool down is reduced so it's easier to handle.
High speed & flicker-free HMI ballast
As with any HMI fixture, the Cinelight HMI PAR lights require a ballast in order to function. The Cinelight HMI electronic ballast complies to the industry's high demanding requirements: flicker free, very low noise, high output and stable long-term operation. The ballast features a rugged and compact design for easy handling on the field.
The ballast employs the ALF technology (Active Line Filter) which minimizes the power line interference, providing a higher Power Factor for a more efficient power use. This translates to a consistent color temperature and flicker-free dimming, despite power line voltage fluctuations.
The dedicated high-speed function of the ballast drives the lamp to 300Hz or 1kHz to ensure a flicker-free image in slow motion shootings.
The ON/OFF power switch on the ballast control panel allows for hot re-striking, while the dedicated dimming knob vary the power down to 50%.
Safety circuits such as over-voltage, over-temperature and short-circuit protection provide a safe and reliable operation.
Wide range of applications in the film industry
These lighting instruments are commonly used to light large setups at night, giving a little more depth to the scenes, and also in situations requiring a far reaching, intense beam. Whenever punch or bounce light is required on a set, the Cinelight PAR is the optimal solution. The daylight-balanced output provided by the HMI fixtures is an essential artificial lighting source for most productions.
Transport case included
For easy transportation and safe storage, a hard plywood case is included which accommodates the kit's components: HMI PAR lamp head, electronic ballast, power cable and metal barndoors.
Specifications
HMI - Fixture
Beam type | spot |
Rated power | 6000 watts |
Lamp type | Single-End |
Lamp socket | G38 |
Color temperature | 6000K |
Lens type | Interchangeable |
Spot-Flood selector type | Mechanical |
Yoke mount | Spigot 28mm pin |
Housing color | Gray & blue |
Housing material | Aluminum |
Lamp head dimensions | 1050 x 700 x 610 cm |
Lamp head weight | 31.3 kg |
HMI - Ballast
Ballast power | 6000 watts |
Ballast line power | 26A-38A |
Ballast nominal current | 6900VA |
Ballast operation voltage | 180-265VAC |
Ballast frequency | 50-60 Hz |
Ballast current characteristics | Square wave, 75Hz |
Ballast power factor | 0.98 |
Ballast dimming range | 100%-50% |
Ballast starting | Hot re-strike |
DMX control | Optional |
DMX connectors type | XLR-3P |
ballast power cable length | 15 m |
Power cord total length | 5.0 m |
Power connector type | CEE 2P+E |
Ballast dimensions | 24 x 37 x 45 cm |
Ballast weight | 26 kg |
Ballast protection class | IP32 |
Q & A ( 0 )
Ask a question
Reviews ( 0 )
- Opening diameters: 38 mm - 52 mm
- Grid clamp / truss eye coupler
- M12 locking bolt with butterfly nut
- Spigot 16 mm (5/8")
- Interior rubberized surface
- Fully metal made
- Spigot length: 70 mm
- Size: 11.5 x 6 x 3 cm | 0.37 kg
- Payload: 25 Kg
- Power: 800W
- Light output: 7650lx (spot) / 1530lx (flood) @ 2m
- Size: 24 x 21.5 x 20 cm | 2.3 kg
- Focusable beam from spot 31° to flood 82°
- Metal housing with heat resistant paint
- High quality interior aluminum reflector
- Optional accessories: softbox, dimmer
- Mounts lighting fixtures on walls and ceiling
- Aka wall plate with baby pin
- Spigot length: 160 mm
- Spigot diameter: 16 mm
- Made of steel
- Size: 12 x 8 x 16 cm | 0.5 kg
- As: F805, KS-045, LF.8005.A, SRP-116P
- Use to extend a combo stand by 95 cm
- Maximum extended length: 95 cm
- Minimum folded length: 70 cm
- Combo mount: 28mm receiver & 16mm spigot
- 28mm die cast aluminum socket with 16mm stud
- Payload: 20 kg
- Stand max height: 530 cm
- Stand min height: 168 cm
- Boom max height: 300 cm
- Boom min height: 133 cm
- Boom length: 148 - 250 cm
- Folded length: 168 cm
- Combo mounts: 28 mm receiver & 16 mm pin
- Convertible upper column in boom arm
- Strong pivoting collar with oversized handle
- Wheels and sand bag included
- Material: steel
- As 546M, KS501311, A4050CS,
- Used to stabilize stands or as counterweight
- Must-have accessory for any grip crew
- Dual zipper ensure secure closure
- Reinforced corners for wear resistance
- 20 kg weight when filled with sand
- Made from Cordura material
- Pocket size: 39 x 23 cm
- Circular frame for holding filters / gels
- Inserted on the accessory holder of Fresnel 150W
- Filters are cut and sandwiched into frame
- Material: steel
- Diameter: 78 mm
- Stand wheels for increased mobility
- Made from high density plastic, inside bearings and rubber coating
- Metal chassis
- Brakes on every wheel
- Required stand leg section: 25x25 mm (square profile)
- As: A9000N, 366170
- Power: 330W
- Light output: 106'000 lx @ 1m
- Lamp type: 2G11 55W
- Size: 66 x 49 x 12 cm | 7.1 kg
- Adjustable brightness 100% - 30% via dimming knob
- Built-in DMX-512 function for remote operation
- Professional Osram Quicktronic HF ballast
- Optional accessories: honeycomb grid, dispersion filter